The Springfield Model 1795 was a .69 caliber flintlock musket manufactured in the late 18th and early 19th centuries in the United States.

Springfield Model 1795
TypeMusket
Place of originUnited States
Service history
In service1795–1865
Used byUnited States
Confederate States
WarsAmerican Indian Wars
War of 1812
Mexican–American War
American Civil War
Production history
DesignerEli Whitney
Designed1795
ManufacturerSpringfield Armory
Harpers Ferry Armory
Various private contractors
Produced1795–1818
No. builtc. 150,000
Specifications
Mass10 lb (4.5 kg)
Length60.0 in (1,520 mm)
Barrel length42.0 in (1,070 mm) to 45.0 in (1,140 mm)

CartridgePaper cartridge, buck and ball/musket ball (.65/16.510 mm) undersized to reduce the effects of powder fouling
Caliber.69 in (17.526 mm)
ActionFlintlock/percussion lock (conversion)
Rate of fireUser dependent; usually 2 to 3 rounds per minute
Muzzle velocity1,000 ft/s (300 m/s) to 1,200 ft/s (370 m/s)
Effective firing range100 to 200 yards, in reality 50 to 75 yards
Maximum firing range300 yards (275 m)[1]
Feed systemMuzzle-loaded
SightsA front sight cast into the upper barrel band

The Model 1795 was the first musket to be produced in the United States by Eli Whitney at both the Springfield and Harpers Ferry U.S. armories. It was based heavily on the Charleville Model 1763/66 which had been imported in large numbers from the French during the American Revolution and which at the time comprised the largest number of muskets in U.S. arsenals at about 20,000 muskets. The Model 1795 was used in the War of 1812, after which shortcomings in both the design and manufacturing process of the Model 1795 led to the development of the Springfield Model 1812 at Springfield only, and eventually the Springfield Model 1816 at both armories.

Characteristics

edit

The Model 1795, a very elongated musket, retained many of the characteristics of the Charleville on which it was based. It had a 44 inches (110 cm) long .69 caliber barrel, a 56 inches (140 cm) stock, and a total length of 60 inches (150 cm). The original version had the bayonet lug on the bottom of the barrel but this was later moved to the top. Minor changes were made throughout production inclusive of a shorter barrel length of 42 inches (110 cm) on the later Harpers Ferry weapons. Barrels of Harpers Ferry Model 1795s were serial numbered up to some point in 1812: Model 1795's were never serial numbered. Springfield began the Model 1812 improvements in 1814, but Harpers Ferry continued on with the production of the Model 1795 until at least 1819 (early 1819 examples still used the Model 1795 lockplate) and never produced the Model 1812. Eventually, both armories incorporated improvements into the Model 1816 flintlock which were after a few years virtually identical. Most, but not all, parts will interchange on the Model 1816 muskets but the hand-crafted parts, and lack of set standards and patterns on the earlier Model 1795 weapons often means parts will not interchange easily.

Typical of smoothbore muskets, the Model 1795 had an effective range of about 50 yards (46 m) to 75 yards (69 m). The Model 1795 fired a smaller round than the British .75 caliber Brown Bess, but the Model 1795 also had both a slightly longer range and slightly better accuracy than the Brown Bess musket. This gave the American forces an advantage of range when they faced British forces in the War of 1812.[2]

Production

edit

The Model 1795 was manufactured at the United States Armory and Arsenal at Springfield, which was the first armory in the United States, at least as early as 1799. Earlier versions prior to this date probably were produced but were not dated. Starting in 1801, possibly as early as 1800, it was also produced in the then new United States Armory and Arsenal at Harpers Ferry. Several differences between the Springfield Model 1795 and the Harpers Ferry Model 1795 have led many to label the Harpers Ferry version as a significantly different model. Quite a few independent contractors also made the weapon as they were in constant demand. The federal armories simply could not make enough muskets to meet demand with the labor force they had during these early years. Only about two dozen artisans worked in the Harpers Ferry arsenal around 1800, and making the muskets from raw materials was a very labor-intensive task. Approximately 80,000 Springfield Model 1795 muskets were produced while about 70,000 were produced at Harpers Ferry.[3]

Service history

edit

Model 1795s were used throughout the War of 1812, the Mexican–American War of 1846–48, and the American Civil War of 1861–65. Most were converted to percussion caps either at the armories or by private individuals, but records reflect that many in the South were issued an original flintlock at the beginning of the Civil War until the Confederates could convert them to percussion. There is some evidence that some were in fact never converted at all from flintlock. The effective service life of the Model 1795 thus extends through 1865.

The Model 1795 was also used by some members of the Lewis and Clark expedition.[4]

Preceded by United States Army rifle
1795-1812
Succeeded by

See also

edit

References

edit
  1. ^ Barbieri, Michael (2013-08-26). "How far is "musket-shot"? Farther than you think". Journal of the American Revolution. Retrieved 2021-06-12.
  2. ^ "Guns in American Society: An Encyclopedia of History, Politics, Culture, and the Law", by Gregg Lee Carter, Published by ABC-CLIO, 2002
  3. ^ Flayderman's Guide to Antique American Firearms, 2001
  4. ^ "Lewis & Clark Tailor Made, Trail Worn: Army Life, Clothing & Weapons of the Corps of Discovery", by Robert John Moore, Robert J. Moore, Jr., Michael Haynes, Published by Farcountry Press, 2003
edit